Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Southlake
Gate parts and welding work in Southlake usually means one of three things: a sagging custom iron gate that’s dragging on the pavers, a hinge post that’s leaning out of plumb from the clay shifting under it, or a cracked weld on ornamental scrollwork that’s been there since the Clinton administration. We fix all three, and we fix them so they stay fixed. Ironworks Gate Co. has been doing gate parts and welding work for over 42 years, and our crews know Southlake’s estate entries the way a mechanic knows a familiar engine. If your gate is binding, grinding, or sitting crooked on its hinges, call (817) 242-5426 and we’ll have a technician out to look at it.
Why Ironworks Gate Co. Is Southlake’s Preferred Gate Parts & Welding Company
Southlake homeowners don’t call around for the cheapest bid. They call because they’ve already had someone out who didn’t fix it right, and they’re tired of watching the gate scrape the driveway every afternoon. Most of our Southlake work comes from referrals on streets off West Southlake Boulevard and Precinct Line Road, where neighbors talk. We show up in uniform, we look at the whole gate system rather than just the part that’s visibly broken, and we give you a written price before we turn a single bolt. That’s the square deal we’ve built the company on since Victor Salinas founded it in 1984.
Our technicians are background-checked and trained on nine gate automation brands, including Viking, DoorKing, and Elite. That matters here because Southlake’s estate gates are rarely one-brand systems. They’re often a hybrid: an older Viking operator retrofitted with newer safety edges, a custom iron panel hung on hinges that were welded to spec twenty years ago. Sorting out what’s actually failing takes someone who understands both the metal and the motor.
Every job we complete in Southlake carries the 90-Day Done Right Promise, in writing. If it’s not right, we come back and make it right. No paperwork, no arguing, no exceptions. That’s how we’ve kept customers on the same streets for decades.
Our Gate Parts & Welding Services in Southlake
Hinge Replacement
Most Southlake estate gates are 16 to 20 feet wide and several hundred pounds, hung on hinges that were originally welded or bolted to masonry pillars. When the black clay under those pillars swells in spring and shrinks through the summer drought, the post leans, the hinge pins wear unevenly, and the gate starts to sag. We cut out the old hinges, re-align the post, and weld in new hardware rated for the actual weight of the panel. A hinge replacement on a typical Southlake swing gate runs $380 to $850 per side, depending on gate size and whether the post needs re-shimming.
Post Replacement
There’s a difference between a leaning post and a failed post. When the footing has cracked or the steel core inside the masonry pillar has corroded through, re-shimming won’t hold. We remove the old post or pillar, pour a new footing sized for Southlake’s expansive clay, and set a new post plumb and square. On estate properties along East Southlake Boulevard, we’ve replaced posts that were set in the late 1990s with footings too shallow for the soil conditions. Post replacement in Southlake typically runs $900 to $2,400 depending on footing depth, pillar reconstruction, and whether we’re matching existing brick or stone.
Rail Repair
Slide gates in Southlake run on rails that take a beating from the clay’s movement and from years of dirt and debris accumulation. When a rail bows or the rollers wear flat, the gate stutters and jerks as it cycles. We straighten or replace rails, set new rollers, and re-level the run so the gate moves without binding. Rail repair work is usually $350 to $1,100 depending on rail length and whether the run needs to be re-bedded in concrete.
Custom Welding
This is where our 42 years of craft shows. Southlake’s custom estate gates are ornamented with scrollwork, finials, and pickets that were often welded by hand when the home was built. When a weld cracks, you can’t just glob on a bead and send it. We match the pattern, grind out the old weld, TIG weld the joint, and blend it so the repair disappears into the original ironwork. Custom welding on ornamental gate frames, finials, and pickets in Southlake runs $180 to $600 per repair point, depending on complexity and finish matching. We recently rebuilt a gate on an estate off West Southlake Boulevard where the 18-foot swing gate had sagged enough to drag on the pavers and trip the safety photocell every afternoon. The hinge post had shifted in the clay, so we cut and re-welded the post footing, replaced the hinge pins with new LiftMaster hardware, and re-hung the panel to clear by a finger’s width. The owner had already had two other companies “fix” the rails and the gate operator. The gate now runs silent and the intercom camera stays aligned.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Southlake
We’re certified and equipped to service nine major gate automation brands, including Viking, Ghost Controls, and Elite. For Southlake customers, that means we typically have the right parts on the truck when we arrive, not in a warehouse three days out. If your estate gate runs on a Viking operator with custom ironwork, we’re familiar with how that specific combination wears over time. We stock common hinge pins, roller assemblies, strike plates, and operator parts for the brands most common in Southlake’s estates, so most Gate Parts & Welding repairs are completed in a single visit.
Common Gate Parts & Welding Problems We See in Southlake Homes
- Hinge post lean from clay shrink-swell: Southlake sits on expansive black clay that swells after spring rains and shrinks hard during summer drought. The cycle pushes gate pillars out of plumb seasonally, which makes the gate drag and forces the safety photocell to fault, putting the operator into constant reversal. If your gate binds every afternoon but seems fine in the morning, this is the likely cause.
- In-ground loop detector failure: Many of Southlake’s estate entries were automated in the late 1990s with in-ground vehicle-detection loops. The clay’s shrink-swell cycle cracks the insulation on those buried loop wires over time, causing the gate to stop closing as a safety default. It gets misdiagnosed as a motor or board problem constantly, until a technician checks the loop signal. On the older estate streets feeding off West Southlake Boulevard, this failure mode repeats predictably.
- Ornamental weld fatigue after ice events: Rare but severe North Texas ice storms, like February 2021, crack custom ironwork at welded joints. The stress transfers to hinges and latch plates, so a gate that survived the ice can still fail months later when the weakened joint finally gives. We see this pattern on gates across 76092 every year after a hard freeze.
- Worn rollers on slide gates: Heavy 18 to 20 foot slide gates wear out roller bearings unevenly when the rail shifts with the soil. The gate starts to shimmy, then jerks, and eventually trips the obstruction sensor. Replacing the rollers and re-leveling the rail fixes the symptom, but on Southlake clay we often recommend re-bedding the rail run so it doesn’t recur next season.
Pricing for Gate Parts & Welding in Southlake, TX
Here’s what Southlake homeowners can expect to pay for common gate parts and welding work. Hinge replacement runs $380 to $850 per side. Post replacement, including footing work, runs $900 to $2,400. Rail repair is $350 to $1,100. Custom ornamental welding runs $180 to $600 per repair point, depending on whether we’re matching existing scrollwork or replacing a cracked finial. What drives the price is the weight of the gate, the condition of the footing, and whether we’re matching custom ironwork or replacing it. Before any work starts, you get a written price. No surprises on the bill. We also offer a free second opinion on any written estimate you’ve received, $50 off any repair over $250, an $89 seasonal tune-up, and a permanent 5% discount for seniors and veterans.
We Also Serve Cities Near Southlake
Our crews work throughout the Southlake area, and we regularly take calls from Colleyville, Grapevine, Bedford, and Keller. If you’re on the edge of Southlake or just across the city line, we’ll still come out. The dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and our trucks are on the road across the metro every day. Call (817) 242-5426 and a live person answers, 24 hours a day.
Serving Southlake, TX - Our Local Coverage Area
We’re based in the Southlake area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Southlake
The hinge posts under your gate are set in expansive black clay, which swells with spring rain and shrinks during the summer drought. The post moves, the gate sags, and the hinges wear unevenly no matter how new they are. That’s why we check the footing and the post plumb before we replace hinges, and why post replacement is often the actual fix. Call (817) 242-5426 and we’ll tell you which one you need, with a written price before we start.
Probably not. On Southlake’s older estate streets, the usual cause is a cracked in-ground loop detector wire caused by the clay’s seasonal movement. The gate sees a false signal and reverses as a safety default. We test the loop signal before touching the board, and in most cases we replace the loop or convert to a photo-eye-only setup. If you’ve been told you need a new board, get a free second opinion from us first.
Yes. We’ve matched custom ironwork on gates across Southlake for 42 years. We grind out the old weld, TIG weld the joint, and blend the repair into the original pattern so it disappears. If a finial is missing or too far gone, we’ll fabricate a replacement that matches the existing profile and patina. The repair is covered by our 90-Day Done Right Promise, in writing.
If the operator is a Viking or Elite unit from the late 1990s or early 2000s and it’s making noise, the issue is usually worn gears or bearings inside the unit, or the gate itself has shifted on its hinges and is putting load on the operator it was never designed to handle. We’ll inspect both, tell you which is failing, and give you a written price for the repair. Forty-two years of doing this work means we’re not going to sell you an operator when the problem is a hinge post out of plumb. Call (817) 242-5426 for a free estimate.
Stand clear of the gate and have someone press the remote while you watch. The gate should reverse immediately if it meets resistance, and the photo-eye should stop it dead if you break the beam. If either fails, the gate is unsafe and the operator will often cycle unpredictably. We test entrapment protection on every service call in Southlake, and we’ll show you what we found before we recommend any repair. Call (817) 242-5426 and schedule a visit.
Call Ironworks Gate Co. for Gate Parts & Welding in Southlake
Your gate is the first thing you see when you come home and the last thing between your family and the street. When it’s sagging, grinding, or refusing to close, you want it fixed by someone who understands the metal, the motor, and the clay under Southlake’s soil. That’s us. Call (817) 242-5426 for a free estimate on any gate parts or welding work in Southlake. A live person answers, 24 hours a day, 7 days a week. We’ll give you a written price before we start, and we’ll stand behind the work in writing for 90 days.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Southlake and the surrounding North Texas area since 1984.