Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLiftMaster Access Control Installation: The Colleyville Owner’s Guide
LiftMaster access control installation in Colleyville typically runs $650 to $1,800 installed, depending on whether it’s a keypad, telephone entry, or a full receiver-and-relay retrofit to an existing operator. We stock LiftMaster-compatible access control components on our trucks and can usually have a straightforward keypad or receiver swap done the same visit. Most owners discover the part has failed when a keypad goes dark, a remote stops being recognized, or the gate stops responding to a specific entry device while everything else still works.
That last one is the tell. When the operator still opens from one control but not another, the motor is fine. The access control component between the button and the board is where the problem lives. We have been called out to Colleyville driveways where a homeowner had already replaced a perfectly good battery in a keypad that had a corroded wire terminal, or bought a whole new operator when the only problem was a $90 receiver that had lost its programming.
Which LiftMaster Models This Applies To
We install and service access control across the LiftMaster gate operator lines most common in Colleyville: the LA400, LA412, LA500, CSL24V, and the older SL3000 and SL585 series that are still out there working on plenty of established properties. The access control side includes LiftMaster keypads like the KPW250 and 412HM, the 850LM and 860LM receivers, MyQ retrofit hubs, and wired telephone entry systems for estate gates.
Here is the compatibility gotcha that trips people up: LiftMaster has changed receiver technology across generations. The older 315 MHz Security+ parts do not talk to the newer Security+ 2.0 components, even when they look almost identical and come from the same brand. If your operator has a purple learn button, you need Security+ 2.0 compatible devices. A red or orange learn button means the older generation. We check this before we sell anything, because installing a receiver that cannot pair with your remotes is a waste of your money and our afternoon.
On OEM versus aftermarket: for receivers and keypads we generally recommend the genuine LiftMaster part. The aftermarket boards we have seen tend to fail early in Texas heat, and the savings of thirty or forty dollars disappears fast when you pay for a second service call. For simple items like photo eyes and external antennas, a quality aftermarket equivalent is usually fine, and we will tell you when that is the case.
Signs Your LiftMaster Access Control Installation Is Failing
- Keypad lights up but the gate will not open. The keypad is transmitting, or thinks it is, but the receiver is not hearing it. This is often a programming loss or a receiver board on its way out, not a dead keypad.
- The gate opens intermittently from one remote but not others. A receiver that works cold and not hot, or vice versa, usually means a failing component on the receiver board itself. Texas summers make this worse, not better.
- Keypad works from the driveway but not from the street. Range that shrinks over time points to an antenna issue or receiver sensitivity loss. Sometimes it is as simple as the antenna wire getting pinched during a past repair.
- You have to press the button twice, or hold it longer than you used to. That hesitation is the first sign of wear on relays or the keypad contact membrane. It only gets slower from there.
- The access control works but the gate slams or creeps open after closing. This is the access control doing its job and the mechanical or limit-switch side failing underneath it. We see this on older Colleyville gates where the hardware was installed decades ago and nobody has touched it since.
The underlying pattern is the same on most of these: the access control part is misdiagnosed as the operator or the motor, and the wrong part gets replaced. That is why we always test the signal path before we quote any replacement.
Replacement Cost & What’s Included
For access control installation in Colleyville, here is the range we quote most often:
- Standalone keypad install: $180 to $420, depending on wired versus wireless and whether we are running conduit or replacing an existing pad with the same footprint.
- Receiver or antenna replacement: $150 to $320, including programming your existing remotes and confirming range from the street.
- Full access control retrofit: $650 to $1,800 for older operators that need new receivers, keypads, and wiring brought up to current building standards. Higher end covers telephone entry or MyQ integration with a cellular backup.
Every quote is settled before we touch a single bolt. You will never see an invoice that surprises you. The part price and the labor are separated on paper, and the price you agree to is the price you pay. All access control work at Ironworks Gate Co. carries the 90-Day Done Right Promise in writing. If it is not right, we come back and make it right, no paperwork, no argument. Senior and veteran customers receive a 5% discount, always, and any repair over $250 qualifies for $50 off.
DIY or Call Us?
Access control work is low-voltage, so you are not dealing with the same danger as a high-tension spring or a swinging gate arm. You can safely check a few things yourself before calling: the battery in a wireless keypad, the power to the operator, and whether the keypad housing shows moisture or ant damage. Ants love keypads. We have opened more than one Colleyville keypad that was more ant hill than electronics.
Where DIY goes wrong is programming and wiring. LiftMaster receivers use specific learn-button sequences, and if you erase a working remote while trying to add a new one, you now have zero working remotes and a gate you cannot open. We have also seen hand-wired keypads where a homeowner swapped two leads and sent 24 volts into a board rated for 12, which turns a $50 visit into a $400 board replacement. If you are not certain, call (817) 242-5426. A live person answers, day or night, and we will tell you over the phone whether it sounds like something you can handle or something we should.
FAQs
A quality LiftMaster keypad in Colleyville lasts 5 to 8 years on average, but direct afternoon sun and the heat inside a metal keypad housing can cut that to 3 to 4. The keypad membrane is usually the first thing to go, not the electronics.
Sometimes. If the issue is corroded terminals, a broken wire, or a dirty contact, we repair it for less than replacement. If the membrane itself is failing or the board is cooked, repair costs more than a new unit, and we will tell you that plainly and let you decide.
A standard keypad or receiver swap takes 45 to 90 minutes on site. A full retrofit with new conduit, wiring, and programming can take half a day, and we will give you a straightforward time window before we start, not after.
Yes. Our Colleyville service trucks carry LiftMaster keypads, receivers, antennas, and common retrofit components, along with parts for Mighty Mule, Ghost Controls, DoorKing, and the rest of the nine brands we service. Most jobs are completed in one visit. Call (817) 242-5426 and we will confirm over the phone that we have your part before we head out.
If your LiftMaster access control is acting up anywhere in Colleyville, from Bransford Road over to Glade and down toward Highway 26, call (817) 242-5426 for a free estimate. A live person answers, we will quote you an honest price before any work begins, and we will stand behind it in writing. That is how we have done it for over 42 years, and that is how we will do it for the next forty.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Colleyville and nearby areas.