Linear Gate Parts & Welding Nationwide

Linear Gate Parts & Welding in Colleyville: What to Know First

We provide independent Linear gate parts and welding in Colleyville, with most hinge, weld, and roller work completed in a single visit. A typical Linear gate repair runs $220 to $480 depending on what gave out, and every price is settled before we turn a wrench. This page is for homeowners in Colleyville whose Linear swing or slide gate has a mechanical problem: a sagging leaf, a cracked weld, a seized roller, or a post that’s starting to lean. Call (817) 242-5426 and a live person answers, day or night.

Call (817) 242-5426

How Linear Products Fail - and How We Fix Them

Linear operators are solid machines, but the gate hardware around them takes a beating in North Texas. Here are the failure patterns we see most often on Linear-equipped gates in Colleyville, and what we do about them.

• Sagging gate leaf on Linear swing systems. The Linear LRA and SWR series openers push a lot of mass through two hinge points, and when the top hinge wallows out even an eighth of an inch, the whole leaf drops. In Colleyville’s clay soil, the post shifts a little each dry season, and the hinge takes the load. We remove the leaf, weld in a new hinge barrel or replace the hinge outright, and re-hang the gate so the operator isn’t fighting gravity. The motor lasts years longer when the geometry is right.
• Cracked welds at the operator mounting plate. Linear swing arms bolt to a plate welded on the gate frame. After enough open-close cycles, the plate’s welds crack from fatigue, often invisible under powder coat. The first sign is a gate that shudders or pauses mid-swing. We grind out the old weld, re-weld with proper penetration, and add a gusset where the design allows. This is a weld we’ve done more times than we can count, and it holds.
• Worn gate rollers on Linear slide gates. The Linear SL and SLR slide operators pull a gate that rides on steel rollers, and those rollers are the sacrificial part. Once the bearings go flat, the gate drags, the operator’s thermal protection trips, and a homeowner thinks the motor died. The motor is usually fine. We swap in new rollers, check rail alignment, and the gate slides like it did when it was installed.
• Post failure behind the hinge. This is the one nobody plans for. In Colleyville, the freeze-thaw cycle works on concrete and the black gumbo clay expands and contracts enough that a gate post can lean a full inch in a decade. When a Linear gate starts scraping the driveway or the latch won’t line up, the post is often the culprit. We dig out the old concrete, set a new or reinforced post plumb, and weld the hinge assemblies back in place. The gate then gets re-adjusted to the operator so the whole system moves as one.
• Latch and lock alignment on Linear-equipped gates. A Linear opener relies on the gate closing fully so the limit switch reads properly. When the latch post shifts, the gate stops a half-inch short, the operator faults, and the keypad stops working the way it should. We realign or replace the latch, weld in a new strike plate where needed, and confirm the limit settings match the new closed position.

Our Linear Gate Parts & Welding Process

Here’s what to expect when you call us for Linear gate work in Colleyville.

1. 1
   We answer and listen. You call (817) 242-5426 and talk to a person, not a menu. We ask what the gate is doing, what it sounds like, and how long it’s been acting up.
2. 2
   We diagnose on site. We inspect the hinges, welds, rollers, posts, and the Linear operator itself. We find the root cause, not just the symptom. That means we don’t replace a motor when a seized roller is the actual problem.
3. 3
   We quote before we work. Parts choice matters here. We use genuine Linear parts where they make a difference, and quality aftermarket steel components where the OEM part is just a marked-up commodity. You’ll know the price, the parts, and the plan before anything starts.
4. 4
   We do the work. Welding, hinge replacement, post reset, roller swap, latch realignment. Our technicians are background-checked and uniformed, and they work in your driveway the way they’d work in their own mother’s.
5. 5
   We test the full system. We run the gate through its full travel multiple times, check the Linear operator’s force settings and limits, and make sure the safety features function properly.
6. 6
   We stand behind it. Every job is covered by our written 90-Day Done Right Promise. If it’s not right, we come back and make it right. No paperwork, no arguing.

What Linear Gate Parts & Welding Costs in Colleyville

Straight numbers, because that’s what you need.

• Hinge replacement (weld-in): $180 to $320 per hinge, depending on gate weight and access
• Weld repair (cracked frame or mounting plate): $140 to $280 per repair point
• Gate roller replacement (pair): $120 to $260 including labor
• Post reset with new concrete: $450 to $850 for a standard single post
• Latch and strike plate realignment: $90 to $220

The price moves based on gate weight, how far the post has shifted, and whether we’re working around an existing operator. Colleyville driveways vary a lot, and so do the fixes. Every estimate is free, and the price you’re quoted is the price you pay. Call (817) 242-5426 and we’ll give you a straight number.

Why Colleyville Homeowners Call Ironworks Gate Co. for Linear Work

We’ve been fixing gates in Colleyville for over 42 years, and Victor Salinas grew up here, not far from Bransford Road, where half the driveways have iron gates and the other half are working up to it. We know Linear equipment because we’ve worked on hundreds of these systems, and because we service eight other major opener brands, LiftMaster, FAAC, BFT, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, we can tell when a Linear operator is the problem and when it’s the hardware around it. We don’t swap parts hoping to get lucky. We find the actual fault, fix it, and back it in writing. A gate that works right doesn’t announce itself. That’s the whole idea.

FAQs