Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Access Control Installation: The Colleyville Owner’s Guide
FAAC access control installation in Colleyville typically runs $450 to $1,200 installed, depending on whether you have a keypad, card reader, or full telephone-entry system going in. We stock FAAC-compatible access control components on our trucks and can usually complete the install the same day we diagnose the failure. Most Colleyville homeowners call us after the keypad stops accepting codes, or after a storm takes out the board and the gate either won’t open or won’t stop opening.
The FAAC access control board sits between the keypad or reader and the gate operator. When it fails, the gate usually still has power, but it has no idea who to listen to. We see this most often on FAAC E024U and 400-series operators that have been in the ground for ten or more years, where the original access control hardware has simply lived past its design life. If your gate opens fine with the remote but ignores the keypad, the access control installation is almost certainly where the problem lives.
Which FAAC Models This Applies To
Our Colleyville service trucks carry access control components that fit the FAAC 400, 402, 412, and E024U operator lines, along with the FAAC 455 D control board setups that still run on plenty of older Colleyville estates. The compatibility detail that matters most is this: FAAC boards have changed connector layouts across production years, so a keypad wired for a 2008 402 will not always drop onto a 2018 412 without an adapter harness or a re-pin job. We match the board revision number, not just the series name, before anything gets wired in.
On the OEM-versus-aftermarket question, our honest position is this: FAAC OEM boards and receivers are the right call when the system is under ten years old and you want it to run another ten. Quality aftermarket equivalents make sense on older gates where the OEM part costs more than the operator is worth and the homeowner wants a dependable fix without a full replacement. We lay out both prices before any work begins, and we only install aftermarket boards from manufacturers we have watched hold up through five or more Texas summers.
Ironworks Gate Co. is an independent gate service company and is not affiliated with FAAC. We simply install and repair their equipment every week.
Signs Your FAAC Access Control Installation Is Failing
- Keypad accepts some codes but not others. This usually points to a failing relay on the access control board itself, not a bad keypad. The board can no longer pass the open signal through to the operator on every attempt.
- Gate opens with the remote but not the keypad or card reader. The operator is healthy. The access control board has stopped listening. This is the most common FAAC failure we see in Colleyville, and it is usually a board or receiver replacement, not a full operator job.
- Gate refuses to close after entering, or reverses before latching. On FAAC systems with safety loops tied into the access control wiring, a failing board can misread the loop signal and think a car is still in the path.
- Keypad display is dead or scrambled. Water intrusion into the keypad housing is a frequent culprit after hard Colleyville rains. The keypad may be fine internally, but the board behind it has taken moisture and needs to be swapped.
- System works intermittently, worse after rain or extreme heat. North Texas weather stresses access control boards in a specific way: summer heat cracks solder joints, and spring thunderstorms find every weak seal. If the gate works at dawn but not at 3 p.m., suspect the board.
Replacement Cost & What’s Included
In Colleyville, a complete FAAC access control installation runs from $450 for a single keypad and board repair up to $1,200 for a full telephone-entry system with a new reader, keypad, wiring harness, and programming. Parts typically represent fifty to sixty percent of the job, with the rest being labor, wire repair, and programming time. Every quote includes the site visit, the diagnostics, the part, the install, clean-up, and a written 90-Day Done Right Promise. The price you approve is the price you pay. No additions, no surprise line items, no “while we were in there” invoices.
We also keep the $89 Seasonal Tune-Up on the books for Colleyville customers who want their access control and operator checked in spring and fall, plus a 5% senior and veteran discount that never expires.
DIY or Call Us?
There are a few checks a Colleyville homeowner can do safely before calling. Confirm the keypad has power. Check that the breaker for the gate has not tripped. Look for obvious water inside the keypad housing or an ant colony that has decided the board is prime real estate. Beyond that, access control installation involves low-voltage wiring, board-level diagnostics, and programming that can brick an operator if done wrong. This is not a dangerous high-voltage job, but it is a job where a wrong wire in the wrong terminal can turn a $450 board replacement into a $1,400 operator replacement.
If you are not certain what board revision you have or what wire goes where, call (817) 242-5426 and we will walk you through it on the phone. If it needs hands, we will schedule the visit. That is what we are here for.
FAQs
We typically see ten to fifteen years of service from a FAAC access control installation in North Texas. Heat is the biggest lifespan factor. Boards mounted inside vented metal enclosures on shaded north-facing walls outlast boards mounted in direct afternoon sun by three to five years.
Sometimes yes, when the problem is a single burned relay or a corroded connector. More often, board-level repair costs within $100 of a new unit, and a new unit comes with a warranty. We will tell you which one makes sense for your gate and your budget, and the quote covers either path before work starts.
Most FAAC access control installations in Colleyville are completed in two to four hours on site. That includes removal, wiring, programming, and testing with your existing remotes and keypads. If the wire run from the house or the keypad needs replacement, add an hour.
We stock common FAAC access control boards, receivers, keypads, and wiring harnesses on our Colleyville service trucks, along with parts for LiftMaster, Mighty Mule, Ghost Controls, BFT, Linear, Viking, DoorKing, and Elite. If your part is not on the truck, our supplier gets it to us within one to two business days in nearly every case. Call (817) 242-5426 and we will tell you honestly what is in stock today.
Victor Salinas grew up in Colleyville, not far from Bransford Road, where half the driveways have iron gates and the other half are working up to it. He trained in welding and electrical systems at Tarrant County College’s northeast campus before spending decades learning the rest of it on real jobs, with real gates, for real neighbors. A gate that works right doesn’t announce itself. That’s the whole idea. So when your gate has announced itself with a dead keypad and a stubborn refusal to open, call us at (817) 242-5426 for a free estimate. A live person answers. We will be there when we say.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Colleyville and nearby areas.