FAAC Gate Installation Nationwide

FAAC Gate Installation in Colleyville: What to Know First

Ironworks Gate Co. provides independent FAAC gate installation in Colleyville for driveway, pedestrian, sliding, swing, and double gate systems. Most FAAC installations run between $2,800 and $7,500 depending on gate size, automation package, and site conditions, and we quote every job before a single bolt gets turned. If you own a FAAC opener and need a new gate hung, an old gate rebuilt, or a complete system installed from scratch, call (817) 242-5426. This page is for Colleyville homeowners who want the straight story on what a FAAC installation actually involves, what it costs here in town, and what can go wrong if corners get cut. No marketing fluff. Just what we have learned on real driveways over 42 years of doing this work.

Call (817) 242-5426

Key Takeaways

• We are an independent FAAC service provider, not a factory-authorized dealer. That means we make parts and repair decisions based on what is best for your gate, not what a manufacturer’s program dictates.
• FAAC hydraulic and electromechanical models each have distinct failure patterns. Knowing which one you have changes how we install, set limits, and protect the motor.
• Every FAAC installation we do carries our written 90-Day Done Right Promise. If something is not right, we come back and make it right. No paperwork, no arguing.
• Live person answers the phone 24/7 at (817) 242-5426. Not an answering service.

How FAAC Products Fail - and How We Fix Them

FAAC makes solid equipment. We have installed and serviced enough of it over the years to know exactly where the weak points are, especially in North Texas clay soil and summer heat. Here is what we see in Colleyville:

• FAAC 400 Series swing gate operators losing thrust in hot weather. The 400 series is a workhorse on Colleyville estate gates, but the hydraulic fluid thins out when August temperatures sit above 100 degrees for weeks. The gate starts to creep or stalls mid-swing. We see this every summer. The fix is usually a fluid check, seal inspection, and adjusting the anti-creep valve. A proper installation should have accounted for Dallas-area heat from the start, which is why we set FAAC hydraulic operators differently than we would for a gate in, say, Ohio.
• FAAC 770 and 844 control board failures after nearby lightning strikes. These boards are robust, but North Texas gets real electrical storms. The 770 series in particular tends to lose its limit memory when a surge hits the line. The symptom is a gate that suddenly swings past its stop point or refuses to close all the way. We install surge protection on every FAAC job that does not already have it. It is a $40 part that saves a $400 board.
• FAAC S800H slide operator limit switches drifting after heavy rains. The S800H is a magnetic limit system, and when clay soil shifts under the gate track during spring rains, the limits fall out of calibration. The gate starts stopping six inches short or slamming into the end stop. We reset and re-secure the limit magnets, then verify the track is still graded true. In Colleyville, a slide gate on shifting soil needs that check at least twice a year.
• FAAC 391 and 540 series running on aftermarket capacitors that burn out in a season. Some “budget” gate installers use no-name capacitors rated for indoor use. They fail fast under a Colleyville sun on a black metal operator housing. We have pulled capacitors so swollen they looked like soda cans. Our rule: OEM or name-brand industrial capacitors only, rated for the actual heat load on your driveway.
• FAAC 750 series locking operators with stripped worm gears from gates that were never properly hung. The 750 needs a gate that swings level and true. If the hinge posts were set out of plumb, the worm gear takes the load it was never meant to carry and eventually strips. At that point the operator is shot. We have replaced enough of them to check post alignment before we even think about mounting the motor. If the gate was poorly hung by a previous contractor, we fix the hang first, then install the operator.

Our FAAC Gate Installation Process

Every FAAC job in Colleyville follows the same path. It keeps surprises off the bill and keeps us from having to come back for something we should have caught the first time.

1. 1
   Call and schedule. You reach a live person at (817) 242-5426. We talk about the gate, the opener model if you know it, and what the problem or project looks like. We set a time. We show up when we say.
2. 2
   Site walk and diagnostic. We look at the gate, the posts, the track or hinges, the operator, the wiring, the sensors. We take measurements. If it is a replacement job, we figure out what can be saved and what needs to go.
3. 3
   Written quote, before work starts. Victor Salinas or one of our senior techs explains exactly what we will do and what it will cost. You approve the number. That number is the number. If we find something hidden during the job, we stop and explain it before proceeding. No surprise invoices.
4. 4
   Installation. This is where the welding, the alignments, the motor mounting, the wiring, and the limit-setting all happen. For FAAC specifically, we set travel limits, force settings, and obstruction sensitivity according to the actual gate physics on your property, not just defaults from the manual.
5. 5
   Full test and demonstration. We cycle the gate open and close. We test the obstruction reversal with a physical block. We test safety edges and photo eyes if installed. Then we walk you through the keypad, the remotes, and the manual release. You see it work before we leave.
6. 6
   The 90-Day Done Right Promise in writing. Every job gets our written guarantee. If anything is not right in the first 90 days, you call, we come back, we fix it. That is the Keystone Standard. We have been doing it for decades.

What FAAC Gate Installation Costs in Colleyville

Here are honest numbers for common FAAC installation scenarios in Colleyville. These are not lowball teasers. They are the real ranges we quote, based on what we see on actual driveways from Bransford Road to the west side.

What moves the price most in Colleyville is soil. Gates on the east side near the creek bottoms need deeper post footings. Gates on grade shifts need more leveling. We quote based on what we see when we stand in your driveway. Estimates are free. Call (817) 242-5426 and we will give you a written price.

Why Colleyville Homeowners Call Ironworks Gate Co. for FAAC Work

We have been in this business since 1984, and we have never stopped being a Colleyville company. Victor Salinas grew up here, not far from Bransford Road, and he trained in welding and electrical systems before spending decades fixing gates that other people installed wrong. When you call us, you get a background-checked, uniformed technician who works in your driveway the way he would work in his own mother’s. We are trained on nine gate-automation brands, so if your FAAC system needs a part we can cross-reference against LiftMaster, Mighty Mule, Ghost Controls, or DoorKing configurations without guessing. And we stand behind every job with the written 90-Day Done Right Promise. Most FAAC jobs in Colleyville are completed in a single visit, with the price agreed and settled before a single bolt gets turned. A gate that works right doesn’t announce itself. That’s the whole idea.

FAQs