Linear Gate Installation Nationwide

Linear Gate Installation in Colleyville: What to Know First

Linear gate installation in Colleyville typically runs $2,800 to $7,500 for a complete single driveway gate with a Linear actuator, depending on gate length, material, and whether we’re automating an existing gate or hanging a new one. Most Linear installations take one full day, and we quote the full price before any work begins. If you’re a Colleyville homeowner with a Linear opener already in hand, or you’re weighing Linear against another brand before a new build, call Ironworks Gate Co. at (817) 242-5426 and we’ll walk you through it in plain terms.

Call (817) 242-5426

How Linear Products Fail - and How We Fix Them

• Linear LRA actuator limit switch drift on older swing gates. The LRA series, common on Colleyville estate gates from the 2000s, uses mechanical limit cams that wear down over years of Texas heat cycling. The gate starts over-traveling by an inch or two, then slams into the post or fails to fully seat. We reset or replace the limit assembly and rebalance the gate so it stops where it should every cycle.
• Linear M3 control board relay failure after storms. North Texas lightning seasons are hard on M3 boards. The open relay welds or the board stops recognizing the safety inputs, and the gate either won’t budge or runs with no obstruction response. We test the full board, replace the relay or the board with a genuine Linear part, and verify every safety input before leaving.
• Gearbox oil leaks on Linear swing and slide actuators. Linear gearboxes are sealed, but ten-plus years of Colleyville summer heat breaks down the seals and the unit starts weeping oil onto the mounting plate. We catch this during installation when homeowners report a “smell” or a stain under the operator. The fix is a gearbox rebuild or swap, done same-day when parts are on the truck.
• Remote receiver desync on Linear Multi-Code systems. Linear’s Multi-Code receivers occasionally drop programmed remotes after a power blink. The homeowner is left holding a working remote that the gate ignores. We re-flash the receiver, check the antenna placement, and if the receiver is genuinely failing, we swap in a new one that plays clean with existing remotes.
• Solar panel undersizing on Linear gate kits. Many Colleyville homes bought Linear solar-ready kits expecting the panel to keep up year-round. It rarely does once trees grow or winter shortens the sun window. We evaluate the actual draw, and when needed, add a second Linear-compatible panel or convert to a hardwired run with a proper transformer so the gate never goes dead mid-cycle.

Our Linear Gate Installation Process

1. 1
   Call and scope. You describe the gate, the opener, and what’s failing or missing. We ask about gate length, material, and whether it’s swing or slide. We set a visit time that works, and a live person answers when you call (817) 242-5426.
2. 2
   On-site evaluation. We measure the gate, check the posts and hinges, inspect the existing Linear operator if there is one, and test the power supply. We look for the problems you called about and the ones you haven’t noticed yet.
3. 3
   Straightforward quote. Before any work begins, we hand you a written price for the full job. That price includes parts, labor, cleanup, and the 90-Day Done Right Promise. It does not change unless you add scope.
4. 4
   The installation. We hang or rehang the gate, mount the Linear operator, run or repair the power, set the travel limits, and wire the safety edges and photo eyes. On Linear jobs we use genuine Linear parts unless a quality aftermarket option is clearly better for your situation, and we tell you which we’re using and why.
5. 5
   Testing and walkthrough. We cycle the gate fifteen to twenty times, test every remote and keypad, trigger the safety edges, and watch how it seats. Then we walk you through operation and maintenance in five minutes without jargon.
6. 6
   Cleanup and guarantee. We leave the site cleaner than we found it and explain the 90-Day Done Right Promise. If anything isn’t right, call us and we come back and make it right.

What Linear Gate Installation Costs in Colleyville

Here are the numbers we quote most often in Colleyville for Linear work. These are honest ranges, not teaser prices, and we settle the exact figure before we touch a bolt.

• Automate an existing swing gate with a Linear LRA actuator: $2,800 to $4,200
• New single swing gate with Linear operator, installed: $4,500 to $7,500
• New double swing gate with two Linear actuators: $7,000 to $12,000
• Slide gate with Linear SLR operator: $5,500 to $9,000
• Pedestrian gate with Linear keypad and strike lock: $1,800 to $3,200

What moves the price: gate length over 14 feet, custom welding, long power runs from the breaker panel, concrete or masonry post work, and whether safety edges or loops need to be added. Call (817) 242-5426 for a free estimate on your exact job. The quote is free, and the price you agree to is the price you pay.

Why Colleyville Homeowners Call Ironworks Gate Co. for Linear Work

We’ve been doing gate work since 1984, and Victor Salinas grew up in Colleyville, not far from Bransford Road. He has worked on Linear openers for more than twenty years and knows which models hold up and which ones need a little more attention in our climate. If your Linear system is beyond saving, we service eight other brands, too: LiftMaster, Mighty Mule, Ghost Controls, DoorKing, FAAC, BFT, Viking, and Elite. That means we won’t push a brand we happen to carry. We’ll tell you honestly what’s worth fixing and what’s not. Every job is protected by our 90-Day Done Right Promise in writing. A live person answers our phone 24 hours a day, 7 days a week, and we’ll be there when we say. As an independent Linear service provider, we’re not affiliated with the manufacturer, and that’s fine by us - it means we answer to you, not to a brand program.

FAQs