Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterMighty Mule Access Control Installation: The Colleyville Owner’s Guide
We install and replace Mighty Mule access control components in Colleyville for a typical installed price of $295 to $640, depending on which control board, keypad, or receiver your system needs. Most access control work is done the same day our truck rolls up, and we keep the common Mighty Mule control parts stocked on board. The way owners usually find us: the keypad stopped accepting the code, the remote worked yesterday and doesn’t today, or the gate started cycling on its own at 3 a.m. None of those are mysteries to us.
What makes Mighty Mule access control different from the other eight brands we service is how much of the system lives in one place. The control board handles the receiver, the limits, and the keypad logic together. When that board goes, it usually takes the convenience features with it while the gate itself keeps moving like nothing happened. You’ll notice the problem in the remotes and keypads first, not in the gate.
Which Mighty Mule Models This Applies To
We work on the full Mighty Mule line that Colleyville homeowners actually have on their driveways: the MM series (MM271, MM371, MM572), the FM series (FM200, FM350, FM500), and the older RB and EZ gate openers that are still out there doing their job two decades in. The access control side of these systems centers on three components: the main control board, the wired or wireless keypad (Mighty Mule’s FM137 and MM137 are the two we replace most), and the receiver module that talks to the remotes.
Here’s the compatibility gotcha that saves people a wasted order: Mighty Mule changed their control board connector layout around 2015. If your system was installed before that, a new board will not plug into the old harness without a retrofit pigtail. We carry both the boards and the pigtails, and we check the board revision before anything gets ordered or installed. On the OEM versus aftermarket question, we have used both. For access control specifically, we lean OEM Mighty Mule boards and keypads because the aftermarket boards have a habit of not talking to the safety sensors on the colder nights we get in north Texas. It saves you money up front and costs you a second trip.
Signs Your Mighty Mule Access Control Installation Is Failing
- The keypad accepts the code but the gate doesn’t move. That’s usually not the gate. That’s the keypad’s relay contact failing on the control board, and the board sends no signal to the motor. The gate itself is probably fine.
- Remotes work only from 10 feet away or less. The receiver antenna circuit on the board degrades slowly rather than dying all at once. In Colleyville, heat in the control box accelerates this more than anything else.
- The gate opens by itself, usually at night. This is stray signal interference or a failing receiver sensitivity pot on the board. We have seen garage door openers, older wireless intercoms, and one very determined ham radio operator cause it.
- One remote stops working while the others are fine. The remote’s own board or battery died. Re-programming a new remote is a five minute job on site, but the remote has to be the right frequency for your board revision.
- The board shows a power light but nothing else responds. This is the classic Mighty Mule board failure we see on gate systems eight years old or more. The power supply is fine, the logic side is gone.
Replacement Cost & What’s Included
For Colleyville homes, Mighty Mule access control replacement and installation runs $295 to $640 installed. The spread comes down to which part failed: a single keypad replacement sits at the lower end, a full control board with new receiver and reprogrammed remotes sits at the higher end.
- Keypad replacement (FM137 or MM137): $120-$190 parts, $95 labor.
- Control board replacement (OEM, current revision): $240-$390 parts, $125-$175 labor.
- Receiver module replacement: $95-$140 parts, $85 labor.
- Full access control refresh (board, keypad, two remotes, reprogram): $520-$640 all in.
Every price is quoted and agreed before we touch a single bolt. The labor to remove, test, install, and re-program the system is included. The parts we install carry the manufacturer warranty, and the whole job is backed by our written 90-Day Done Right Promise. If it is not right, we come back and make it right. No paperwork, no arguing.
DIY or Call Us?
Access control is one of the safer areas to troubleshoot on a gate system, because the control board runs on low voltage and doesn’t carry the 120V line current. That said, the moment a homeowner opens the control box and sees the wiring, most of them close it back up. Mighty Mule boards use a tight multi-pin connector layout, and forcing a connector into the wrong header sends 12V somewhere it should not go, turning a $150 part into a $450 board swap.
What we tell our Colleyville customers: check the obvious. Make sure the keypad batteries are good, the control box lid is sealed, and nothing chewed through the low-voltage wire where it runs along the fence line. That is where we have found more rabbits than we care to count. If the board is getting power and the keypad is lit but the gate will not respond to a command, call us at (817) 242-5426. The part you need is probably on our truck, and the fix is usually done in under an hour.
FAQs
Eight to twelve years is the honest range we see in Colleyville, where summer heat inside an unshaded control box shortens board life compared to cooler climates. Install a small sun shield over the box and you’ll add years. Call (817) 242-5426 for a free estimate on replacement, and we’ll check the box placement while we’re there.
Rarely. For boards older than 2015, the failed relay or capacitor is often repairable, but board-level repair costs nearly the same as a new OEM board once labor is counted. We’ll tell you plainly which route makes sense for your system, and we don’t make money either way because the quote is agreed before work starts.
A keypad is done in 30 minutes. A full board and receiver swap, with remotes re-programmed and safety sensors tested, runs 60 to 90 minutes. We stock common Mighty Mule control parts on the truck, so most Colleyville jobs are completed in one visit.
We stock the control boards, keypads, and receivers for the Mighty Mule MM and FM series most common in Colleyville, and we stock parts for LiftMaster, Ghost Controls, and DoorKing systems as well. If your system needs a part we don’t have on board, we order it and we’re back out within a few days.
When your gate stops listening to you, it is rarely the gate. It is the access control. Victor Salinas trained in welding and electrical systems at Tarrant County College before spending two decades figuring out exactly which board, keypad, or receiver is the one that failed, and he still believes a gate that works right doesn’t announce itself. That’s the whole idea.
If your Mighty Mule access control is acting up anywhere in Colleyville or nearby, call Ironworks Gate Co. at (817) 242-5426. A live person answers, day or night. We’ll give you an honest price before we start, do the job in one visit when the part is common, and stand behind it in writing.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Colleyville and nearby areas.