Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterViking Gate Installation in Colleyville: What to Know First
Viking gate installation in Colleyville typically runs $1,800 to $6,400 for a complete driveway gate with automation, and most jobs are measured, quoted, and scheduled within five to ten business days. We install Viking swing gates, slide gates, and pedestrian gates as an independent service provider, which means we’re not tied to any manufacturer’s price book or schedule. If you own a Viking panel and need it hung, welded, automated, or wired, call (817) 242-5426 and we’ll give you a straight answer on cost and timing before anyone picks up a tool. This page covers what Colleyville homeowners actually need to know before putting a Viking gate in the ground.
How Viking Gates Fail - and How We Fix Them
- Swing gate hinge sag on heavier Viking ornamental panels. Viking’s steel ornamental line, especially double-wide driveway panels, puts a lot of weight on the top hinge. Over time in Colleyville’s clay-heavy soil, the post shifts a few degrees and the gate starts dragging on the latch side. We see it most on gates hung ten or more years ago. Our fix is a re-hang with heavier-gauge post reinforcement, not just another weld on the old hinge barrel. A fresh weld on a fatigued hinge buys a year. Reinforcing the post buys the next thirty.
- Slide gate roller wear on Viking cantilever models. Cantilever slide gates ride on rollers that take the full gate weight every cycle. When a roller bearing goes flat, the gate starts shuddering mid-travel and eventually the motor stalls. Colleyville’s fine dust from dry summers works its way into the rollers and accelerates the wear. On Viking cantilever installs, we replace rollers in sets and check the track alignment at the same time, because a new roller on a misaligned track will fail again within a season.
- Control board failures after lightning season. North Texas gets real electrical storms. Viking control boards, particularly on older R6 and R12 series operators, are sensitive to power surges and nearby strikes. The board will show power but refuse to respond to the remote or keypad. We carry both OEM Viking boards and a proven aftermarket replacement that handles surge conditions better on exposed Colleyville properties. The aftermarket option costs less and, frankly, we have had fewer callbacks on it than the original part.
- Photo eye misalignment from gate post movement. The safety photo eyes on Viking automation are mounted on the gate posts or adjacent columns. When soil shifts, the posts move a fraction of an inch and the eyes lose their alignment. The gate then refuses to close, or reverses mid-travel for no visible reason. Homeowners call confused because nothing looks broken. We realign the eyes and anchor the posts, then cycle the gate twenty times to confirm the fix holds through a full temperature swing.
- Worn drive belts on Viking slide operators. The toothed belt inside a Viking slide operator stretches with age and heat. Once it slips, the gate jerks instead of gliding, and the motor works harder every cycle until it overheats. We replace the belt at the first sign of jerking, before the heat damages the motor itself. On a Viking job, that single step saves most owners the cost of a full operator replacement six months down the road.
Our Viking Gate Installation Process
Here is how a typical Viking installation goes from first call to final walk-around, based on jobs we have run in Colleyville for years:
- 1
Call and talk to a person. You call (817) 242-5426, a live person answers, and we schedule a site visit. No voicemail trees, no waiting for a callback. We ask about your gate, your opener, and what it is doing or not doing.
- 2
Site measure and honest assessment. Victor Salinas or one of our techs comes out, measures the opening, checks the posts, the existing automation if any, and the power situation. We tell you what is salvageable and what is not. If the posts are solid, we say so. If they need to come out, we say that too.
- 3
Written price before any work. The quote is fixed and written. You approve it before we order a single part or turn a single bolt. If the job changes mid-way because of something we find underground, we stop and talk to you first. No surprise invoice at the end.
- 4
Parts decision, made together. We stock OEM Viking parts and quality aftermarket equivalents. We show you the difference in cost and tell you honestly which one makes sense for your gate and how long you plan to stay in the house. The decision is yours.
- 5
Installation, wiring, and testing. We hang the gate, weld and reinforce as needed, mount the operator, run the power and safety circuits, and program the openers. Then we cycle the gate repeatedly, load-test it, and check the safety edges and photo eyes under real conditions.
- 6
Cleanup and the Done Right Promise. We clean the work area, walk you through operation and maintenance, and hand you the written 90-Day Done Right Promise. If anything is not right, we come back and fix it. No paperwork, no arguing.
What Viking Gate Installation Costs in Colleyville
Here are the honest price ranges we are quoting for Viking work in Colleyville right now. These are installed prices including parts, labor, and the warranty:
| Viking Job Type | Typical Colleyville Price Range |
|---|---|
| Single swing gate, manual (no automation) | $1,800 - $3,200 |
| Single swing gate with Viking operator | $3,400 - $5,200 |
| Double swing gate with Viking operator | $4,800 - $6,400 |
| Cantilever slide gate with Viking operator | $4,200 - $6,800 |
| Pedestrian gate with Viking keypad entry | $1,400 - $2,600 |
| Viking operator retrofit on existing gate | $1,100 - $2,400 |
What moves the price is post condition, power distance from the house, gate size and weight, and whether excavation is needed. A gate with failing posts costs more than one with solid columns already in place. Call (817) 242-5426 for a free, written estimate on your specific opening. We quote the job before any work begins, and that price holds unless you change the scope.
Why Colleyville Homeowners Call Ironworks Gate Co. for Viking Work
We have been doing gate work in Colleyville for over 42 years, and Victor Salinas grew up here, not far from Bransford Road. That matters when you are deciding who to trust with your driveway. We are not a handyman who says he can figure out a Viking opener. We carry Viking parts on the truck and we understand how their control boards behave in a Texas lightning storm. If a Viking panel is not the right fit for your posts or your power situation, we will tell you plainly. And because we service eight other opener brands including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, we never push a brand that does not fit the job. Every Viking installation we complete is covered by our written 90-Day Done Right Promise. If it is not right, we come back and make it right. That is the whole agreement.
Frequently Asked Questions
A Viking gate installation in Colleyville typically costs between $1,800 and $6,800 depending on gate size, automation, post condition, and power access. A basic single swing gate without automation runs $1,800 to $3,200, while a cantilever slide gate with a Viking operator runs $4,200 to $6,800. Call (817) 242-5426 for an exact quote on your opening. Estimates are free and the price is fixed before work starts.
Most Viking gate installations in Colleyville are scheduled within five to ten business days of your initial call. Measure and quote happen on the first visit, and installation is scheduled once you approve the written estimate. If your gate is a safety issue or your property is unsecured, call us and we will tell you honestly how soon we can get out there.
No. Installing a Viking operator on a Viking gate does not void the manufacturer warranty when the work is done to spec with correct voltage, proper grounding, and safety circuits wired correctly. As an independent Viking service provider, we install to the manufacturer’s requirements so your warranty stays intact. We also back the installation itself with our 90-Day Done Right Promise.
Yes. We regularly re-set and re-hang existing Viking gates in Colleyville when the original posts have shifted or rusted at the base. The gate panels are almost always salvageable. We dig out the old posts, pour new footings sized for our soil conditions, and re-hang the gate level and square before mounting the operator. Call (817) 242-5426 for a free assessment of your posts.
That depends on the gate’s age, steel condition, and whether the failure is in the panel or the automation. A Viking gate with solid metal and a failing operator is almost always worth repairing. A gate with rust-through at the hinge mounts or structural fatigue is usually cheaper to replace in the long run. We will show you both options with honest numbers and let you decide. No sales pressure, just facts.
Ready to Talk About Your Viking Gate?
If your Viking gate needs to be installed, re-hung, automated, or replaced, call (817) 242-5426 and talk to a live person. We will schedule a site visit, give you a written price before any work begins, and stand behind the job with the 90-Day Done Right Promise. Victor Salinas and the Ironworks Gate Co. team have been serving Colleyville for over 42 years, and we plan to be here for the next forty. A gate that works right does not announce itself. That is the whole idea.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving Colleyville and nearby areas.